Description
Joining 220V AC mains leads, 12V/24V DC power wires, or load connections using twisted tape splices or weak plastic connectors causes loose contacts, heat buildup, and messy troubleshooting. The KF-25 2-Pin Terminal Block – 300V 30A Black Screw Wire Connector for AC & DC Circuits available at Rafiq Electronics provides a sturdy, two-way screw-clamped connection point rated up to 30A at 300V AC/DC. Featuring two isolated screw terminals inside a compact black insulating housing, this KF-25 2-Pin Terminal Block lets you fasten and release solid or multi-strand copper wires cleanly with a standard screwdriver while keeping positive/negative or live/neutral lines separated and secure. To understand how screw-clamped terminal blocks provide reliable, serviceable wire connections in electrical and electronics setups, read about Screw terminals on Wikipedia.
Built with high-conductivity metal clamping contacts and a durable black insulating plastic body, this KF-25 2-Pin Terminal Block grips stripped copper conductors firmly without chewing through fine wire strands and allows effortless rewiring during repairs or circuit upgrades. Its compact two-pin format makes single-line AC or DC power termination neat, fast, and vibration-resistant on power boards, enclosures, and bench test rigs.
Electronics technicians, appliance repairers, solar/inverter builders, and DIY makers rely on this KF-25 2-Pin Terminal Block for clean, reusable two-wire connections.
Whether you are terminating a 12V/24V DC supply line, connecting 220V AC input/output leads on a power board, or building a custom bench test rig, this 300V 30A Black Screw Wire Connector keeps connections safe and organized.
KF-25 2-Pin Terminal Block Key Features & Connection Advantages
-
300V 30A AC & DC Rating: Built to handle currents up to 30A across voltages up to 300V AC/DC for dependable power and load wiring.
-
Compact 2-Pin Dual-Terminal Layout: Two separate screw terminals keep positive/negative or live/neutral conductors cleanly isolated side by side.
-
Firm Screw-Clamp Wire Grip: Tightens down solidly onto stripped copper wires to prevent accidental pull-outs and maintain low contact resistance.
-
Reusable & Serviceable Design: Loosen or retighten screws anytime with a screwdriver without cutting wires or desoldering permanent joints.
-
Durable Black Insulating Housing: Tough molded plastic body isolates both terminals cleanly for safer panel and enclosure routing.
-
Broad AC & DC Circuit Support: Suitable for low-voltage DC battery/module wiring as well as AC mains and power supply circuits within rating limits.
Technical Specifications
| Parameter | Details |
| Product Name | KF-25 2-Pin Terminal Block – 300V 30A Black Wire Connector |
| Model Number | KF-25 (2-Pin Variant) |
| Pin Configuration | 2-Pin (2-Position Screw Terminal Block) |
| Rated Voltage | Up to 300V AC / DC |
| Rated Current | Up to 30A |
| Housing Color | Black |
| Operating Circuit Type | AC & DC Circuits |
| Connection Method | Screw-Clamp Wire Termination |
| Primary Applications | Power Boards, Enclosures, DIY Circuits & Electrical Wiring |
Practical Power, Repair & DIY Applications
-
Power Supply & Controller Boards: Terminate two-wire AC mains input or DC output leads cleanly onto power cards, driver modules, and custom enclosures.
-
Bench Testing & Prototype Wiring: Connect or swap power and load test leads rapidly during circuit debugging without permanent solder joints.
-
Clean Wire Prep & Inspection: Strip and trim wire ends cleanly using our YTH-109 Electronics Wire Cutter Pliers, solder board pins or tin ends neatly with our Original 60W Soldering Iron Kit with Solder Paste & 0.8mm Wire and Broza Soldering Flux Paste, and check continuity/voltage with the DT830 Digital Multimeter.
-
Multi-Pin & Higher-Amperage Alternatives: For four-wire 30A connections, check our KF-25 4-Pin Terminal Block, or choose our KF-45 2-Pin Terminal Block for heavier 40A power distribution.
Safe Wiring & Installation Guidelines
Always switch off 220V AC mains power and disconnect DC battery or power supplies completely before stripping wires or tightening terminal screws. Strip insulation cleanly so bare copper sits squarely inside the terminal clamp with no stray strands touching the neighboring screw, tighten both screws firmly without over-torquing, and keep continuous current within 30A.






Reviews
There are no reviews yet.